If the BMW Multi-Controller (Wonder Wheel) will not control your CHIGEE Display, start with your control method and RC setting. The cradle connection, CGRC pairing, motorcycle configuration or electrical system may need checking.
Try these fixes first
Park and identify whether you use native BMW factory navigation cradle control or a CGRC CAN or CGRC LIN module.
On the CHIGEE Display, open Settings > Peripheral > RC. Select Nav for supported native control or CGRC for the corresponding module.
For supported native BMW factory navigation cradle or CGRC LIN control, if the BMW TFT shows TFT~Nav, press and hold Menu Up to select the navigation interface. Check whether the Multi-Controller (Wonder Wheel) now controls the CHIGEE Display. CGRC CAN does not require NAV focus.
For native control, turn on Vertical Rolling Control to move the cursor on supported phone-mirroring pages. BMW analog dashboards do not show the TFT~Nav logo or use this TFT-based control method.
If the problem continues
Use the check below that matches your CHIGEE Display’s connection.
The TFT~Nav logo is missing
For a mechanical BMW factory navigation cradle, seat the CHIGEE Display fully and lock the cradle with its original key. Check again for TFT~Nav.
If the logo appears only when the CHIGEE Display is pressed gently into place while parked, the contact fit may be unreliable. Have the cradle inspected; power alone does not prove a reliable control connection.
For BMW factory navigation cradle for Navigator 5 or 6, confirm the cradle is genuine and unmodified. Identify the installed cradle with the BMW factory navigation cradle guide. Aftermarket or modified cradles need a compatibility check.
You use CGRC CAN or CGRC LIN
For CGRC control, confirm the module is connected to a supported BMW interface. A steady blue indicator shows paired operation; flashing red or no light can indicate a pairing, power or connection problem.
Check the CHIGEE Display’s CGRC selection and Bluetooth pairing. Reconnect the module if needed, then check the indicator and control response.
Note: The AIO-5 EVO, XR-2 and AIO-6 EVO do not support CGRC CAN or CGRC LIN.
Control worked before and then stopped
If Multi-Controller (Wonder Wheel) control previously worked on the same CHIGEE Display installation, report what changed. Check for loose accessible connections and, for CGRC, the indicator and pairing status.
Activate navigation preparation (SA 272 / option 272)
SA 272, also called option 272, is BMW’s equipment code for “navigation preparation (SA 272).” BMW also uses the name “navigation preparation (SA 272).” This motorcycle-side configuration enables navigation equipment to be operated with the BMW Multi-Controller, commonly called the Multi-Controller (Wonder Wheel).
On supported BMW motorcycles, SA 272 must be active for native Multi-Controller (Wonder Wheel) control of a compatible CHIGEE Display. SA 272 is not required for native BMW data reading. BMW’s Multi-Controller and Navigator guidance explains the navigation-preparation requirement for BMW navigation equipment.
You can share the BMW ISTA activation demonstration, starting at 2:23, with your BMW dealer or service center. It shows SA 272 activation using BMW ISTA (Integrated Service Technical Application), BMW’s diagnostic and workshop software. The video is a reference for the dealer, who must verify the procedure for your motorcycle.
When should you ask for SA 272 activation?
Ask a BMW dealer to check SA 272 if your motorcycle supports native Multi-Controller (Wonder Wheel) control but control still fails after the connection, cradle and RC checks above. A fitted cradle and a powered CHIGEE Display do not confirm that SA 272 is active.
The dealer should check whether SA 272 is already active before making changes. If it is inactive, ask the dealer to confirm that navigation preparation can be activated for your motorcycle.
Before the dealer starts
The cradle checks below apply to a BMW factory navigation cradle for Navigator 5 or Navigator 6 installation. For another cradle type, have the dealer verify the requirements for your setup.
Confirm that the BMW factory navigation cradle for Navigator 5 or Navigator 6 cradle is genuine and unmodified.
Seat the CHIGEE Display securely in the cradle and lock it in place.
Keep the CHIGEE Display powered throughout the update. Do not remove the display or disconnect power while the update is running.
Tell the dealer: “I need to use the BMW navigation cradle and control my CHIGEE Display with the handlebar Multi-Controller. Check and activate navigation preparation (SA 272), SA 272 / option 272, and update the BMW navigation-preparation software or firmware as required for my motorcycle.”
What the BMW dealer needs to do
SA 272 activation is carried out through the motorcycle’s BMW workshop system. Ask the dealer to use the following checklist with the procedure for your exact model and year.
Connect BMW ISTA. Connect the workshop computer to the motorcycle’s On-Board Diagnostics (OBD) port using a suitable diagnostic interface. Identify the motorcycle and read its equipment configuration.
Check the navigation connection. Use the BMW wiring information in ISTA to locate and verify the 3-pin navigation connector, X740*1B. See Find the BMW 3-pin navigation interface for reference diagrams. Have the dealer check battery voltage, vehicle wiring and the cradle connection.
Confirm SA 272 availability and status. Ask the dealer to find navigation preparation (SA 272), SA 272 / option 272, in the motorcycle’s equipment or retrofit options. The dealer must verify that the option and procedure apply to your motorcycle.
Activate navigation preparation. If SA 272 is inactive and supported, the dealer should carry out the applicable BMW activation procedure. Ask the dealer to complete any required BMW factory navigation cradle software or firmware update while keeping the CHIGEE Display powered.
Verify activation and test control. Ask the dealer to confirm that the work completed successfully and SA 272 is active. With the motorcycle parked, select Nav under Settings > Peripheral > RC on the CHIGEE Display. On supported TFT-equipped motorcycles, press and hold Menu Up to select navigation control. Confirm that the CHIGEE Display responds to Multi-Controller (Wonder Wheel) input.
BMW’s ConnectedRide Cradle information (PDF) also describes navigation preparation and workshop retrofitting on eligible models. The dealer must check eligibility for your motorcycle; that document describes BMW’s ConnectedRide Cradle rather than CHIGEE compatibility.
If Multi-Controller (Wonder Wheel) control still does not work
If a known-working, compatible BMW motorcycle is available, test your CHIGEE Display on its navigation cradle while parked. This can help distinguish a display issue from a problem with your motorcycle’s cradle or navigation connection.
If control still fails after the checks and activation, have the BMW dealer inspect the cradle contacts and navigation connector for damage. A damaged cradle or connector may need replacement.
If SA 272 cannot be activated or native control remains unavailable, a compatible CGRC CAN may provide an alternative. Check compatibility with your BMW and CHIGEE Display before purchasing.
Contact us
Contact us with your BMW model and year, CHIGEE Display model and firmware, connection method and whether TFT~Nav appears. Include existing results and a parked video if useful; do not repeat tests you already reported.
Taiwan: help your dealer identify SA 272
BMW factory navigation cradle must be active for native Multi-Controller (Wonder Wheel) control on supported motorcycles. In a customer-reported case in Taiwan, the dealer did not recognize the SA 272 code or English name because the local system used a Chinese name.
Ask your BMW dealer to look for “導航準備工作” (Navigation Preparation), highlighted in blue in the customer-provided screenshot below. Show the screenshot to help the dealer identify the option in their system.
The customer confirmed that Multi-Controller (Wonder Wheel) control worked after this option was activated. The dealer must still verify the correct option and procedure for your motorcycle.

